OkBike Logo
OkBike Logo
Home Verified Garages Serviceable Pincodes Hotspots Demand Partner (Mechanic Portal)
Book Doorstep Service Get on Google Play

Choose Your City

Explore verified bike garages & doorstep service across India

Language:

Fault Code U0143 Diagnostic Solution

Step-by-step diagnostic checks, multimeter testing values, wiring inspections & OBD-II erase guides for BS6 two-wheelers.

OkBike App Icon

OkBike Mechanic App

Live sensor graphs, 1,000+ color wiring diagrams, ECU pinouts & OBD-II scanner.

U0143
Network & CAN-Bus Communication
Standard OBD-II Diagnostic Protocol
Share with Mechanic
Fault Description & Technical Meaning:

Lost Communication With Body Control Module C. This diagnostic trouble code indicates that the electronic control module has stopped broadcasting heartbeat messages over the CAN serial data communication network. The Body Control Module (BCM) manages exterior lighting, turn signals, horn, hazard lamps, security immobilizer, and power distribution. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.

Diagnostic Summary: Diagnostic code U0143 triggers due to a lost communication affecting the Body Control Module (BCM), impacting proper vehicle operation.

Related Components (Photo & Inspection)

3 Components (Tap to Zoom)
EOT Sensor (Engine Oil Temperature)
Sensor

EOT Sensor (Engine Oil Temperature)

Click to inspect photo & test specs

12V Motorcycle Battery
Electrical

12V Motorcycle Battery

Click to inspect photo & test specs

Circuit Fuse
Electrical

Circuit Fuse

Click to inspect photo & test specs

Common Symptoms
  • • Check Engine Light (MIL Lamp): Illuminates or flashes on the speedometer console.
  • • Engine Hesitation & Jerking: Poor throttle response during sudden acceleration.
  • • Drop in Fuel Economy: Open-loop fuel spraying increases petrol consumption and causes black smoke.
  • • Hard Cold Starting: Engine dies during idle or requires multiple starter button attempts.
Common Root Causes
  • • Wiring Harness Damage: Chafed wires touching motorcycle frame metal or rodent cuts.
  • • Loose / Corroded Coupler: Green oxidation or loose push-fit pins inside connector plug.
  • • Defective Component: Burnt internal sensing thermistor or solenoid actuator coil.
  • • Low Battery Voltage: Weak motorcycle battery under 12.0V causing ECU reference error.

Step-by-Step Diagnostic & Repair Procedure

Bench-tested repair procedure for code U0143

5 Steps
Step 1: Turn off the vehicle ignition switch, remove the key, and allow all electrical and mechanical systems to cool down completely. Locate the Body Control Module (BCM), typically positioned located inside the main battery box or front fairing cowl panel.
Step 2: Carefully unplug the electrical wiring coupler from the Body Control Module (BCM). Inspect the connector pins and socket terminals for green copper corrosion, water moisture, bent pins, or melted plastic. Trace the wiring harness back toward the control module and check for chafing, wire cuts, or melted insulation touching vehicle metal.
Step 3: Set a digital multimeter to DC Volts and turn the ignition key ON without starting the engine. Check for proper electrical reference voltage (5.0V reference or 12V battery power depending on component specification). Next, set the meter to Ohms (continuity) and verify 12V unswitched battery power, 12V switched ignition power, ground pins (< 0.2 Ohms), and CAN-H / CAN-L continuity to the module to ensure the ground circuit has less than 0.5 Ohms resistance to the chassis ground.
Step 4: Bench-test the component by measuring its internal resistance across the electrical terminals using your multimeter (main fuse power feeds, switched ignition line, and CAN-bus communication twisted pair). If the component is carbon-fouled, contaminated, or has poor pin tension, clean it carefully using dedicated electrical contact cleaner. If the internal coil or sensor circuit shows zero Ohms (short) or infinite Ohms (open), replace the component with a genuine OEM part.
Step 5: Reconnect the electrical coupler firmly until the locking tab audibly clicks into place. Connect an OBD-II diagnostic scanner or use the OkBike Mechanic App to erase stored DTC fault memory from the ECU. Start the engine or power up the vehicle, perform a test drive covering varied speeds, and verify that the Warning Light remains permanently turned off.
Important Note: Simply replacing the sensor does not immediately clear the Check Engine Light (MIL). Connect an OBD-II scanner to the motorcycle diagnostic connector and execute "Erase Stored DTC Memory" followed by a road test.

Related Diagnostic Fault Codes

U0140 Lost Communication With Body Control Module. This diagnostic trouble code indicates that the electronic control module has stopped broadcasting heartbeat messages over the CAN serial data communication network. The Body Control Module (BCM) manages exterior lighting, turn signals, horn, hazard lamps, security immobilizer, and power distribution. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
U0141 Lost Communication With Body Control Module A. This diagnostic trouble code indicates that the electronic control module has stopped broadcasting heartbeat messages over the CAN serial data communication network. The Body Control Module (BCM) manages exterior lighting, turn signals, horn, hazard lamps, security immobilizer, and power distribution. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
U0142 Lost Communication With Body Control Module B. This diagnostic trouble code indicates that the electronic control module has stopped broadcasting heartbeat messages over the CAN serial data communication network. The Body Control Module (BCM) manages exterior lighting, turn signals, horn, hazard lamps, security immobilizer, and power distribution. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
U0144 Lost Communication With Body Control Module D. This diagnostic trouble code indicates that the electronic control module has stopped broadcasting heartbeat messages over the CAN serial data communication network. The Body Control Module (BCM) manages exterior lighting, turn signals, horn, hazard lamps, security immobilizer, and power distribution. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
U0145 Lost Communication With Body Control Module E. This diagnostic trouble code indicates that the electronic control module has stopped broadcasting heartbeat messages over the CAN serial data communication network. The Body Control Module (BCM) manages exterior lighting, turn signals, horn, hazard lamps, security immobilizer, and power distribution. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
U0146 Lost Communication With Serial Data Gateway Module A. This diagnostic trouble code indicates that the electronic control module has stopped broadcasting heartbeat messages over the CAN serial data communication network. The Serial Data Network Communication Bus carries multiplexed diagnostic and operational message frames between all onboard microprocessor control units. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.