OkBike Logo
OkBike Logo
Home Verified Garages Serviceable Pincodes Hotspots Demand Partner (Mechanic Portal)
Book Doorstep Service Get on Google Play

Choose Your City

Explore verified bike garages & doorstep service across India

Language:

Fault Code P00FE Diagnostic Solution

Step-by-step diagnostic checks, multimeter testing values, wiring inspections & OBD-II erase guides for BS6 two-wheelers.

OkBike App Icon

OkBike Mechanic App

Live sensor graphs, 1,000+ color wiring diagrams, ECU pinouts & OBD-II scanner.

P00FE
Powertrain Diagnostic
Standard OBD-II Diagnostic Protocol
Share with Mechanic
Fault Description & Technical Meaning:

EVAP System Tank Vapor Line Restricted/Blocked. This diagnostic trouble code has detected an abnormal operating condition or electrical signal failure. The EVAP Canister Purge Solenoid Valve draws stored gasoline vapors from the fuel vapor canister into the combustion chamber to prevent atmospheric fuel emissions. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.

Diagnostic Summary: Diagnostic code P00FE triggers due to a circuit malfunction affecting the EVAP Canister Purge Solenoid Valve, impacting proper vehicle operation.

Related Components (Photo & Inspection)

3 Components (Tap to Zoom)
EOT Sensor (Engine Oil Temperature)
Sensor

EOT Sensor (Engine Oil Temperature)

Click to inspect photo & test specs

EVAP Purge Solenoid Valve
Actuator

EVAP Purge Solenoid Valve

Click to inspect photo & test specs

12V Motorcycle Battery
Electrical

12V Motorcycle Battery

Click to inspect photo & test specs

Common Symptoms
  • • Check Engine Light (MIL Lamp): Illuminates or flashes on the speedometer console.
  • • Engine Hesitation & Jerking: Poor throttle response during sudden acceleration.
  • • Drop in Fuel Economy: Open-loop fuel spraying increases petrol consumption and causes black smoke.
  • • Hard Cold Starting: Engine dies during idle or requires multiple starter button attempts.
Common Root Causes
  • • Wiring Harness Damage: Chafed wires touching motorcycle frame metal or rodent cuts.
  • • Loose / Corroded Coupler: Green oxidation or loose push-fit pins inside connector plug.
  • • Defective Component: Burnt internal sensing thermistor or solenoid actuator coil.
  • • Low Battery Voltage: Weak motorcycle battery under 12.0V causing ECU reference error.

Step-by-Step Diagnostic & Repair Procedure

Bench-tested repair procedure for code P00FE

5 Steps
Step 1: Turn off the vehicle ignition switch, remove the key, and allow all electrical and mechanical systems to cool down completely. Locate the EVAP Canister Purge Solenoid Valve, typically positioned plumbed along the fuel vapor line under the fuel tank or near the intake manifold vacuum port.
Step 2: Carefully unplug the electrical wiring coupler from the EVAP Canister Purge Solenoid Valve. Inspect the connector pins and socket terminals for green copper corrosion, water moisture, bent pins, or melted plastic. Trace the wiring harness back toward the control module and check for chafing, wire cuts, or melted insulation touching vehicle metal.
Step 3: Set a digital multimeter to DC Volts and turn the ignition key ON without starting the engine. Check for proper electrical reference voltage (5.0V reference or 12V battery power depending on component specification). Next, set the meter to Ohms (continuity) and measure the signal wire voltage and ground continuity with a digital multimeter to ensure the ground circuit has less than 0.5 Ohms resistance to the chassis ground.
Step 4: Bench-test the component by measuring its internal resistance across the electrical terminals using your multimeter (solenoid internal coil resistance (typically 25 to 40 Ohms) and 12V switched battery power with key ON). If the component is carbon-fouled, contaminated, or has poor pin tension, clean it carefully using dedicated electrical contact cleaner. If the internal coil or sensor circuit shows zero Ohms (short) or infinite Ohms (open), replace the component with a genuine OEM part.
Step 5: Reconnect the electrical coupler firmly until the locking tab audibly clicks into place. Connect an OBD-II diagnostic scanner or use the OkBike Mechanic App to erase stored DTC fault memory from the ECU. Start the engine or power up the vehicle, perform a test drive covering varied speeds, and verify that the Warning Light remains permanently turned off.
Important Note: Simply replacing the sensor does not immediately clear the Check Engine Light (MIL). Connect an OBD-II scanner to the motorcycle diagnostic connector and execute "Erase Stored DTC Memory" followed by a road test.

Related Diagnostic Fault Codes

P00FB Turbocharger Outlet Pressure Sensor A Circuit High. This diagnostic trouble code indicates that circuit voltage exceeds the maximum allowable threshold (typically indicating a short-circuit to 12V battery power or a missing ground). The Turbocharger / Supercharger Boost Control System modulates forced-induction intake boost pressure and wastegate actuation to prevent engine over-boost and maintain optimal torque. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P00FC Turbocharger Outlet Pressure Sensor A Intermittent/Erratic. This diagnostic trouble code indicates intermittent signal dropouts or electrical noise caused by loose pin tension, vibration-induced wiring chafing, or cracked solder joints. The Turbocharger / Supercharger Boost Control System modulates forced-induction intake boost pressure and wastegate actuation to prevent engine over-boost and maintain optimal torque. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P00FD Battery B State of Charge Performance. This diagnostic trouble code indicates an in-range rationality fault where the sensor is sending a signal, but the value contradicts other sensor readings or expected physical limits. The 12V Battery & Charging System supplies clean electrical power to the vehicle ECU, fuel pump, ignition coils, and electronic sensors. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P00FF Body Control Module Requested MIL Illumination. This diagnostic trouble code has detected an abnormal operating condition or electrical signal failure. The Powertrain Diagnostic Subsystem controls essential electronic fuel, air, and ignition parameters to maintain stable combustion and low exhaust emissions. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P0100 Mass or Volume Air Flow Sensor A Circuit. This diagnostic trouble code has detected an abnormal operating condition or electrical signal failure. The Mass Air Flow (MAF) Sensor measures the exact mass and volume of air entering the engine intake so the computer can calculate precise fuel injection quantity. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.
P0101 Mass or Volume Air Flow Sensor A Circuit Range/Performance. This diagnostic trouble code indicates an in-range rationality fault where the sensor is sending a signal, but the value contradicts other sensor readings or expected physical limits. The Mass Air Flow (MAF) Sensor measures the exact mass and volume of air entering the engine intake so the computer can calculate precise fuel injection quantity. When this circuit fails, the vehicle computer illuminates the Check Engine / Warning Light and may log an active diagnostic fault code.